Top
Boat ESC

FlyMonster

Unique Desigen,  Dual-ways watercooling.

Buy now
PRODUCT FEATURES

img-1.jpgimg-2.jpgimg-3.jpgimg-4.jpg

SPECIFICATION
Model
Battery
Con. Current
Burst Current(10S)
BEC
Weight
Size
Firmware
Typical Applications
Product features
FlyMonster-50A
FlyMonster-70A
FlyMonster-90A
FlyMonster-120A
FlyMonster-150A
2-6s
2-6s
2-6s
2-6s
2-6s
50A
70A
90A
120A
150A
300A
420A
540A
720A
900A
5.5V/5A
5.5V/5A
5.5V/5A
5.5V/5A
5.5V/5A
90g
101g
102g
155g
169g
57×49×18mm
57×49×18mm
57×49×18mm
76×56×25mm
76×56×25mm
-
-
-
-
-
Boat length<55cm
Boat length<70cm
Boat length<100cm
Boat length<120cm
Boat length<135cm

● Use powerful & high performance MCU. Users can set functions as their demand, fully embody Intelligent characteristics. Unique circuit design, strong anti-interference.

● Waterproof design(Note: if there is water in the ESC, Please dry the water at the connectors).

● Start mode can be set. throttle response fast, and it has a very smooth speed control linearity. Compatible with scale boat & racing boat .

● Low-voltage protection threshold value can be set.

● Built-in switch BEC, large power load with servo, lower power dissipation.

● Multiple protection functions: input voltage abnormal protection/ low-voltage cutoff protection, over-thermal protection and throttle signal loss protection, make the ESC more reliable.

● High power safety performance: wherever the throttle lever is, the motor will not start immediately.

● Over thermal protection: when ESC temperature is over 100 °C, output power will automatically reduce. When it's lower than 80°C output power will return to normal.

● Cycle menu setting, simple operation. Support setting with program box and transmitter.

TECHNICAL SUPPORT
船模编程卡 BCK-S006-A1A1
对航模电调进行相应设置。使用非常方便,只需要先把想要设置的功能在编程卡上设定好,也就是把编程卡上的选择帽(红色)插入相对应功能接口,然后把(红、白、黑)信号线接口插入编程卡对应的(ESC)接口,(注:未带 BEC 输出的,请在“– +”加入 5VDC), 上电后听到电机“滴”的一声后,设置成功。
Immediate purchase
Troubleshooting
1. When the boat is switched on, the ESC beeping sound can indicate numbers of battery cells, but the motor is not started
Reset the throttle range.
2. The ESC is functional without any alarm but the motor is not started.
1. Check the plug of motor cables or solder motor cables again. 2. Change a new motor.
3. When the boat is switched on, the ESC beeps (two beeps with short pause)
The battery voltage is too low to drive the boat. Replace it by a fully charged battery.
4. When the boat is switched on, the ESC beeps (two beeps with short pause)
1. Check the connection of signal cables and receiver. 2. Check transmitter and receiver make sure the communication is functional.
5. When the boat is switched on the ESC beeps constently.
Pull the throttle stick to bottom position or reset the throttle range.
6. When the motor is switched on the ESC beeps two long tones and two short tones.
Choose proper setting of throttle forward or backward.
7. The boat is running reversely
1. Switch any two cables of the three cables connecting ESC and motor. 2. Use remote controller or program card to reverse rotation of the motor.
8. The motor stops while the boat is running
1.Set proper value of Low Voltage Protection. When the protection is triggered the boat would be running at Low Power Mode. And it means you should retreat your boat.2. The boat should be running in the range of remote controller. Mind the battery voltage of the remote controller. If it drops magnificently you should retreat your boat.
9. The motor stops while the boat is running
1. Check setting of remote controller. 2. Check the communication between controller and receiver. 3. Check if there is interference from other electronic devices. Try to reconnect power cable if the boat back to normal function. If the same issue occurs frequently it could be caused by strong electromagnetic interference. Changing location of game is recommended.
10. The motor stops while the boat is running
Check the connections of battery plug, power cables and motor cables.

If you have any ideas or Suggestions about our products, please let us know